Forged from ordnance steel to strict, national match specs; rifled by a proprietary technique that holds lands and grooves to exceptionally close tolerances and leaves the surface finish mirror smooth. Air gauged to maintain .0002" tolerance through the bore. Feed ramps are throated for wadcutter ammo. Standard Barrel - Non-ramped, oversize hood, top and bottom lugs to achieve an exact fit for optimum match accuracy. Ramped Barrel - Fully supports the case head; gives direct feeding from magazine to chamber. Requires machining of frame. Gunsmithing fitting required.
Std - Standard barrel, non-ramped. W/N - Wilson/Nowlin Ramp. C/P - Clark/Para Ordnance Ramp
SPECS: 4150 ordnance steel, in-the-white. Available in 5” (12.7cm), 6” (15.2cm), or Commander 4.25” (10.8cm) lengths.
To complement our “Ring-Of-Steel” Action Wrench System, we’ve developed the only professional-quality Barrel Vise that will positively clamp and keep even the tightest barrel from turning during removal. Machined from solid steel for durability to service the barrel installation and removal needs of any gunsmith for years and years. Our exclusive four bolt system and extra-wide design generates so much holding force, the Brownells Barrel Vise must be firmly bolted to the stoutest bench or an immovable base to realize its full potential. Split barrel bushings come in a variety of sizes to fit many popular barrels (and some not-so-common ones) to make this universal Barrel Vise system the very first choice of professional gunsmiths. Steel Bushings provide years of service and have the necessary clamping power to break loose the tightest barrels. Aluminum Bushings also give a strong hold without risk of marring your barrel.
SPECS: Blocks - Steel, blued. Top Block - 4-1⁄2" (11.4cm) x 3" (7.6cm) x 1-1⁄2" (3.8cm). Bottom Block - 7" (17.7cm) x 3" (7.6cm) x 1-1⁄8" (2.8cm). Includes 4, 1⁄2"-20 x 2" Allen head bolts. Bottom block is drilled and countersunk for 1⁄2" diameter mounting bolts. Bushings - C.R.S. Steel, blue finish or 6160 aluminum, natural finish. All bushings 3" long, -13⁄4" diameter. #4, 7, 8, 9, 10 and 11 are in a range of I.D.’s to closely match the shank diameters of most rifle barrels. #5 fits military Mauser 98 barrels. #6 is tapered to fit Remington factory .30-06 Sporter and other similar profile barrels. #12 & 13 are a special machined set of bushings for standard and heavy M14/M1A/M1 Garand barrels. #15 is for the FN FAL barrel. #16 is an aluminum bushing for ¾" octagonal barrels. Steel and Aluminum Barrel Vise Sets come complete with the four ½"-20 tpi x 2" Allen head bolts, hex wrench, and bushings #4, #6, #7, #8, #9, #10 and #11. (Bushings #5, 12, 13, 14, 15 and 16 must be purchased separately).
Compatible with all M-LOK handguards and forends, these rail sections allow you to attach 1913 Picatinny rail-mounted accessories to your weapon. Rail sections are available in either aluminum or polymer. Aluminum sections are machined from Mil-Spec anodized aluminum. Lightweight polymer sections are injection molded from a proprietary reinforced composite for enhanced strength and durability. Both aluminum and polymer rail sections feature beveled ends to eliminate sharp corners and edges, plus reduce snagging. Includes all necessary hardware for attaching rails to M-LOK slots on aluminum or polymer handguards and forends.
SPECS: Aluminum or polymer, matte black. 3 Slots – 1-1/2" (3.8cm) OAL. 5 Slots – 2-3/8" (6cm) OAL. 7 Slots – 3-1/8" (7.9cm) OAL. 9 Slots – 3-7/8" (9.8cm) OAL.